The tongue and groove paneling installed over drywall is a popular option to add style and beauty to a room. This type of paneling can be installed in many ways, but each requires careful measurement and precision cutting. Most panels are attached to furring strips which run vertically along the wall. This is the most popular method. Another option is to place panels diagonally. This involves cutting a 45° angle at the ends of each panel in order to form the long groove side.
Installation Steps
You must remove all hooks, outlets and nails from walls before hanging wood planks. Also, you'll need to sand any protrusions from the walls. To accomplish this task, you can use a power or large sandpaper section and an extension base.
Find out if your tongue-and-groove paneling is nailed or screwed to drywall.
You can check whether your tongue and groove wall panels are properly nailed onto drywall by placing a prybar in the corner of each wall where they meet. With your hammer, tap the prybar into a seam where the two walls meet. You will need to remove the panel from the wall if it isn't nailed to the drywall using a prybar and pliers.
Check whether the tongue and groove walls panels are nailed to or glued.
Once you've determined that your paneling is nailed to drywall, begin by removing any trim that's still attached to the wall. In the ideal case, you can reuse the trim.
If you cannot reuse the trim, you will need to purchase new wood panels. You will need four sheets of 4'x8" wood paneling to cover the walls you want. Measure the wall width and divide that number by 4. If you have walls greater than 8 feet tall, subtract one panel for each door and one panel for each window.
Drywall: Marking a straight edge
You can ensure that the wood paneling is properly installed across the drywall surface by running a straight line from one end to the other. Check for areas where the ceiling or drywall extends beyond the wood paneling. Your paneling might not lay flat if it bulges.
Dust Mask for Drywall Sanding
If you are installing tongue-and-groove paneling over drywall, remove any drywall. This will enable your paneling to fit more evenly and be easier to install.
Finishing with a Wood Putty
After you've sanded down the drywall, apply a coat of wood putty to the walls and the paneling to seal the joints between the walls and the paneling. The paneling can also be stained with a wood stain for a more natural look. However, this requires more labor than applying paint.
Drywall Paneling Attachment
You will need a nail set that has rounded heads to attach wood paneling and drywall. These fasteners are available at most hardware stores and cost about $4 per pack of 16-penny common nails. These nails can be used with any wood type, including plywood anddrywall. If you want to install thicker boards, however, you may prefer construction staples or pneumatic quickeners.
FAQ
How important is it that you are preapproved for a loan?
Getting pre-approved for a mortgage is very important because it gives you an idea of how much money you need to borrow. It will also help you determine if you are qualified for a specific loan program.
Do you prefer to hire a general contractor, or a subcontractor for your project?
Hiring a general contractor is usually more expensive than hiring a subcontractor. General contractors usually have many employees. This means that they charge their clients much more for labor. A subcontractor, on the other hand, only hires one worker, and charges less per hour.
How can I avoid being ripped off while renovating my home?
Knowing what you're paying for is the best way to avoid being scammed. Make sure you read every word of the contract before signing it. Also, don't sign blank contracts. Always ask for a copy of the signed contract.
Statistics
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- On jumbo loans of more than $636,150, you'll be able to borrow up to 80% of the home's completed value. (kiplinger.com)
- They'll usually lend up to 90% of your home's "as-completed" value, but no more than $424,100 in most locales or $636,150 in high-cost areas. (kiplinger.com)
- It is advisable, however, to have a contingency of 10–20 per cent to allow for the unexpected expenses that can arise when renovating older homes. (realhomes.com)
External Links
How To
How much should I spend on restoring my house?
How many rooms you wish to renovate, the type of renovations that you are planning, where you live and whether you hire professionals or yourself will all affect how much it costs. The average cost for renovations is $10,000 to $50,000 depending on how large and complex the project.
If you're planning to sell your home after the renovation, you'll likely receive less than market value if you don't take into account the costs of repairs, upgrades, and improvements. If you do not put in enough effort to make your home attractive before selling, you might lose money. However, investing enough energy and time into improving the appearance of your home can help increase the value you get for it when you list it.
These factors can help you make a decision about which projects to take on first.
-
Your budget. If you have a limited budget, start small. You can start small, for example, by tackling one room at a given time. To make big changes, you can hire a contractor who is skilled in kitchen remodeling.
-
Priorities. Do you want to improve the overall condition of your home or just fix specific problems? If you choose to tackle only one issue, keep in mind that minor issues can add up quickly. It is possible to end up replacing your roof sooner than anticipated if your roof leaks whenever it rains.
-
Your timeline. Consider your timeline. If you are looking to purchase a new home next year, for example, you might not want to replace your bathroom fixtures or install hardwood floors right away. Instead, you might wait until you move out of your existing home to make those updates.
-
Your skills. You might not have the skills to complete a project. A cabinet maker might be available to help you if your carpentry skills do not allow you to make custom cabinets.