The seam at the end of the tub's flange will meet the backerboard on the back wall of a bathtub is common. This is the area where caulk will be used to seal the seam. You may have to patch some areas if the seam is not sealable. You must follow all procedures when installing a tub surround.
Make sure the back wall of the tub is level. Before you install the tub surround, remove the old one. This can be done with a pry bar, or a Hammer. Wear protective gear.
You have the option to put a tub surround in concrete, wood or tile depending on what you need. There are many options for these surrounds. Plastic panels or acrylic are the most popular. Each type has its specific installation instructions. Some kits include only one back panel, others include two. You can save money by purchasing a single-piece surround.
Once the surround is removed, it's time to take out the corners. To measure the new surround, you will need to measure it. It is crucial to use the right adhesive for it to stick. It is important to not apply adhesive to more than one area at a given time. Give it time to dry.
When you're ready for the adhesive to go on, mark the left- and right-sides of your wall along with the top and base of the surround. This will give you a visual reference point for where to apply the adhesive. Make sure you cut the adhesive lines precisely. To make the lines clearer, masking tape may be used.
Next, place the surround's backpiece against the wall. Finally, adjust the back to make it flush. The back should be flat against the drywall. If the back piece is not level, you'll need to add some extra adhesive to the gap. After applying the adhesive, you'll need to let it dry for at least 24 hours.
Now you can put in the tub surround's rear wall. This is the most straightforward part. It's best to have someone hold it to ensure that it doesn't move. Alternatively, you can set a level across the surface and use it to guide the installation.
After that, attach the flanges onto the studs. Pre-drilled holes should be slightly larger so that fasteners can be driven through them. Two to four nailers are recommended for added support. They should be attached to the walls, but not to the wall framing.
Before you start tiling, you will need to install the appropriate vapor barrier. A vapor barrier is thick plastic sheeting that protects the wall from moisture. Paint and primer will be needed. There are many kinds of glue to choose from, so make sure to read the directions carefully.
FAQ
What time does it take to finish a home remodel?
It depends on the size of the project and the amount of time that you spend each day. The average homeowner works on the project for three to six hour a week.
Do you prefer to hire a general contractor, or a subcontractor for your project?
It is more expensive to hire a general contractor than to subcontract. General contractors usually have many employees. This means that they charge their clients much more for labor. A subcontractor, on the other hand, only hires one worker, and charges less per hour.
How do you make a house look new?
These are the steps to follow when renovating your house without spending a lot of money.
-
Create a budget plan
-
Find out which materials you require
-
Decide where you want them to go
-
Make a list.
-
Find out how much money your have
-
Plan your renovation project
-
Start working on your plans
-
Do some research online
-
Ask family members and friends for help
-
Get creative!
Statistics
- On jumbo loans of more than $636,150, you'll be able to borrow up to 80% of the home's completed value. (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- The average fixed rate for a home-equity loan was recently 5.27%, and the average variable rate for a HELOC was 5.49%, according to Bankrate.com. (kiplinger.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- ‘The potential added value of a loft conversion, which could create an extra bedroom and ensuite, could be as much as 20 per cent and 15 per cent for a garage conversion.' (realhomes.com)
External Links
How To
How can I plan a complete house remodel?
Planning a home remodel takes planning and research. There are many things you should consider before starting your project. The first thing to do is decide what kind of home renovation you want. You can choose from a variety of categories, such as kitchen or bathroom, bedroom, living space, or living room. After you decide which category you want to work on, figure out how much you can afford to spend on the project. If you are new to working in homes, budget at least $5,000 for each room. If you have experience, you may be able to manage with less.
Once you have established how much you are able to afford, you will have to decide on how big a job to do. If you have only enough money to remodel a small kitchen, you may not be able add new flooring, countertops, or paint the walls. On the other hand, if you have enough money for a full kitchen renovation, you can probably handle just about anything.
Next, you need to find a contractor who is experienced in the type project that you want. This will guarantee quality results, and it will save you time later. After you have selected a professional contractor, you can start to gather materials and supplies. Depending on the size of your project, you may need to buy everything from scratch. However, there are plenty of stores that sell pre-made items so you shouldn't have too much trouble finding everything you need.
Now it's time for you to start planning. Begin by sketching out a rough plan of where furniture and appliances will be placed. Then, you'll move onto designing the layout of the rooms. Remember to leave enough space for outlets and plumbing. Make sure to position the most visited areas close to the front door. Visitors can also easily access them. Final touches to your design include choosing the right colors and finishes. You can save money by using neutral colors and simple designs.
Now that your plan is complete, it's time you start building! Before you begin construction, it's important to check your local codes. While permits are required in some cities, homeowners can build without one in others. First, remove all walls and floors. To protect your flooring, you will lay plywood sheets. You will then attach or nail pieces of wood together to make the cabinet frame. Finally, attach doors and windows.
When you're done, you'll still have a few finishing touches to do. You'll likely want to cover any exposed wires and pipes. For this, you will use plastic sheeting or tape. Also, you will need to hang mirrors or pictures. You should always keep your work area clean.
You'll have a functional home that looks amazing and is cost-effective if you follow these steps. Now that you are familiar with how to plan a whole home remodel project, it is time to get started.